PROBLEM SYMPTOMS TABLE
IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH: This system uses the body control system, so check the body control system before you proceed with troubleshooting ( DI-1038 ).
|
Symptom |
Suspect Area |
| Ignition switch is not set to each position. | 4. Ignition switch 5. Power source circuit |
| Ignition key illumination does not light up. | 1. Bulb 2. Body ECU 3. Wire Hauness |
| Key unlock warning system does not operate. (The buzzer does not sound when the driver's door is opened with the ignition OFF and key inserted) |
1. Key Unlock Warning Switch 2. Door Courtesy Switch 3. Wire Harness |
| Key unlock warning system does not operate. (The buzzer sounds when the ignition key is in ACC or ON) |
1. Ignition Switch 2. Wire Harness |
HEADLIGHT AND TAILLIGHT SYSTEM: This system uses the body control system, so check the body control system before you proceed with troubleshooting ( DI-1038 ).
|
Symptom |
Suspect Area |
| "Automatic light control system" does not operate. | 1. Automatic Light Control Sensor 2. Light Control Switch 3. Door Courtesy Switch 4. Wire Harness |
| Auto turn-off system does not operate when the driver's door is opened. | 1. Drivers Door Courtesy Switch |
| Auto turn-off system: Headlight and taillight do not come on. | 1. Body ECU 2. Wire Harness |
| Auto turn-off system: Headlight and taillight stay on. | 1. Body ECU 2. Wire Harness |
| Only one headlight comes on. | 1. Daytime Running Light No.3, 4 Relays
2. Body ECU 3. Bulb 4. Wire Harness |
| "LO-beam" does not light (All). | 1. Engine Room J/B Relay Circuit 2. Wire Harness |
| "LO-beam" does not light (One side). | 1. Bulb 2. H-LP L-LWR Fuse 3. H-LP R-LWR Fuse 4. Wire Harness |
| "HI-beam" does not light (All). | 1. Headlight Dimmer Switch
2. Body ECU 3. Wire Harness |
| "HI-beam" does not light (One side). | 1. Bulb 2. H-LP L-UPR Fuse 3. H-LP R-UPR Fuse 4. Daytime Running Light No.3, 4 Relays 5. Wire Harness |
| "Flash" does not light. | 1. Headlight Dimmer Switch
2. Body ECU 3. Wire Harness |
| Headlight does not come on. | 1. Engine Room J/B Relay Circuit
2. Body ECU 3. Daytime Running Light No.3, 4 Relays 4. Headlight Dimmer Switch 5. Light Control Switch 6. Wire Harness 7. Bulb |
| Headlight does not come on with light control switch in HEAD. | 1. Light Control Switch 2. Wire Harness |
| Headlight does not go out with light control switch in OFF. | 1. Engine Room J/B Relay Circuit 2. Wire Harness |
| Headlight flickers. | 1. Bulb 2. Wire Harness |
| Headlight is dark. | 1. Bulb 2. Wire Harness |
| Taillight does not come on with light control switch in TAIL. | 1. Engine Room J/B Relay Circuit 2. Light Control Switch 3. Wire Harness |
| Taillight does not go out with light control switch in OFF. | 1. Engine Room J/B Relay Circuit 2. Light Control Switch 3. Wire Harness |
| Headlight does not come on with engine running and light control switch in OFF | 1. ECU-B1 Fuse 2. ECU-IG1 Fuse 3. Body ECU 4. Daytime Running Light No.3, 4 Relays 5. Generator L Terminal 6. Parking Brake Switch 7. Wire Harness |
FOG LIGHT SYSTEM:
|
Symptom |
Suspect Area |
| Fog light does not light up with light control SW HEAD (Headlight is normal.) | 1. FOG Fuse 2. Engine Room J/B Relay Circuit 3. Fog Light Switch 4. Wire Harness |
| Fog light does not light up with light control SW HEAD (Headlight does not light). | 1. *1 Other Parts 2. Wire Harness |
| Only one light does not light up. | 1. Bulb 2. Wire Harness |
*1: Inspect Headlight System
TURN SIGNAL AND HAZARD WARNING SYSTEM:
|
Symptom |
Suspect Area |
| "Hazard" and "Turn" do not light up. | 1. ECU-IG2 Fuse 2. TURN HAZ Fuse 3. Ignitioin Switch 4. Turn Signal Flasher Relay 5. Wire Harness |
| Hazard warning light does not light up. (Turn is normal) |
1. Hazard Warning Switch 2. Wire Harness |
| Turn signal does not light up. (Hazard is normal) |
1. Turn Signal Switch 2. Wire Harness |
| Turn signal does not light up in one direction | 1. Turn Signal Switch 2. Wire Harness |
| Only one bulb does not light up. | 1. Bulb 2. Wire Harness |
INTERIOR LIGHT SYSTEM: This system uses the body control system, so check the body control system before you proceed with troubleshooting( DI-1038 ).
|
Symptom |
Suspect Area |
| All the lights do not come ON. | 1. DOME Fuse 2. Body ECU 3. DOME Relay(Cowl Side J/B LH) |
| The light does not come ON when the driver's door is opened. | 1. Driver's Door Courtesy Switch 2. Wire Harness |
| The light does not come ON when the passenger's door is opened. | 1. Passenger's Door Courtesy Switch 2. Wire Harness |
| The light does not come on when the rear-right door is opened. | 1. Rear-Right Door Courtesy Switch 2. Wire Harness |
| The light does not come on when the rear-left door is opened. | 1. Rear-Left Door Courtesy Switch 2. Wire Harness |
| Only one of the bulbs comes ON. | 1. Bulb |
| The illumination does not fade out when all the doors are closed. | 1. Courtesy Switch
2. Wire Harness 3. Boby ECU |
| The illumination does not fade out immediately when the ignition switch is turned to ACC or ON within 15 seconds after all the doors are closed. | 1. Ignition Switch
2. ACC Fuse 3. ECU-IG1 Fuse 4. Body ECU 5. Wire Harness |
| The illumination does not fade out immediately when all the doors are locked within 15 seconds after they are closed. | 1. Door Unlock Detection Switch 2. Wire Harness |
| Room light does not light up. | 1. Bulb 2. Room Light 3. Rear Personal Light 4. Wire Harness |
| Front personal light does not light up. | 1. Bulb 2. Front Personal Light 3. Room Light 4. Wire Harness |
| Rear Room light does not light up. | 1. Bulb 2. Rear Room Light 3. Wire Harness |
| Vanity light does not light up. | 1. Bulb 2. Vanity Light 3. Wire Harness |
| Glove compartment light does not light up. | 1. Bulb 2. Glove Compartment Courtesy Switch 3. Wire Harness |
| Courtesy light does not light up. | 1. Bulb 2. Door Courtesy Switch 3. Wire Harness |
BACK-UP LIGHT SYSTEM:
|
Symptom |
Suspect Area |
| Back-up Light does not light up. | 1. GAUGE2 Fuse 2. Ignition Switch 3. Wire Harness 4. Bulb |
| Back-up Light remains always on | 1. Park/ Neutral Position Switch 2. Wire Harness |
| Only one light does not light up. | 1. Bulb 2. Wire Harness |
STOP LIGHT SYSTEM:
|
Symptom |
Suspect Area |
| Stop light does not light up. | 1. STOP Fuse 2. Stop Light Switch 3. Wire Harness |
| Stop light always lights up | 1. Stop Light Switch 2. Wire Harness |
| Only one light always lights up. | 1. Wire Harness |
| Only one light does not light up. | 1. Bulb 2. Wire Harness |
WIPER AND WASHER SYSTEM:
|
Symptom |
Suspect Area |
| Front wiper and washer do not operate | 1. WIPER Fuse 2. Wiper Switch 3. Wiper Motor 4. Wire Harness |
| Front wiper does not operate in LO or HI | 1. Wiper Switch 2. Wiper Motor 3. Wire Harness |
| Front wiper does not operate in INT. | 1. Wiper Switch 2. Wiper Motor 3. Wire Harness |
| Front washer motor does not operate | 1. WASHER Fuse 2. Washer Switch 3. Washer Motor 4. Wire Harness |
| Front wiper does not operate when washer switch is ON. | 1. WASHER Fuse 2. Washer Switch 3. Wiper Motor 4. Wire Harness |
| Rear wiper does not operate. | 1. RR WIPER Fuse 2. Rear Wiper Motor 3. Rear Wiper Switch 4. Rear Wiper Relay 5. Wire Harness |
| Rear wiper does not operate in INT or ON position. | 1. Rear Wiper Switch
2. Rear Wiper Relay 3. Wire Harness |
| Rear wiper does not return to OFF position. | 1. Rear Wiper Motor 2. Wire Harness |
| Rear washer motor does not operate. | 1. Rear Washer Motor
2. Rear Washer Switch 3. Wire Harness |
| Washer fluid does not operate. | 1. Washer Hose and Nozzle |
*1: Inspect wiper arm and blade set positions.
COMBINATION METER (Meter Gauges and Illumination):
|
Symptom |
Suspect Area |
| Tachometer, fuel gauge and engine coolant temperature gauge do not operate | 1. GAUGE2 Fuse 2. Combination Meter 3. Wire Harness |
| Speedometer does not operate. | 1. Speed Sensor 2. Combination Meter 3. Wire Harness |
| Tachometer does not operate. | 1. Igniter 2. Combination Meter 3. Wire Harness |
| Fuel gauge does not operate or is in abnormal operation. | 1. Fuel Receiver Gauge
2. Fuel Sender Gauge 3. Combination Meter 4. Wire Harness |
| Oil pressure gauge does not operate. | 1. Oil Pressure Receiver Gauge
2. Oil Pressure Sender Gauge
3. Combination Meter 4. Wire Harness |
| Voltmeter does not operate. | 1. Voltmeter 2. Combination Meter 3. Wire Harness |
| Engine coolant temperature gauge does not operate or is in abnormal operation | 1. Engine Coolant Temperature Receiver Gauge
2. Engine Coolant Temperature Sender Gauge
3. Combination Meter 4. Wire Harness |
| All illumination lights do not light up. | 1. Light Control Rheostat 2. Wire Harness |
| Brightness does not change even when rheostat is turned. | 1. Bulb 2. Wire Harness |
| Only one illumination light does not light up. | 1. Bulb 2. Wire Harness |
COMBINATION METER (Warning Light):
|
Symptom |
Suspect Area |
| Warning lights do not light up. (Except discharge, open door and SRS) | 1. GAUGE1 Fuse 2. Combination Meter 3. Wire Harness |
| Fuel level warning light does not light up. | 1. LED 2. Combination Meter 3. Fuel Sender Gauge 4. Wire Harness |
| ABS warning light does not light up. | 1. LED 2. ABS ECU 3. Wire Harness |
| Seat belt warning light does not light up. | 1. LED 2. Seat Belt Buckle Switch 3. Wire Harness 4. Body ECU |
| Discharge warning light does not light up. | 1. METER Fuse 2. LED 3. Wire Harness 4. Generator |
| Brake warning light does not light up. | 1. LED 2. Parking Brake Switch 3. Brake Fluid Level Warning Switch 4. LED Check Relay 5. Combination Meter 6. Wire Harness |
| SRS warning light does not light up. | 1. ECU-B2 Fuse 2. LED 3. Airbag Sensor Assembly 4. Combination Meter 5. Wire Harness |
| Open door warning light does not light up. | 1. DOME Fuse 2. LED 3. Door Courtesy Switch 4. Combination Meter 5. Wire Harness |
| A/T oil temperature warning light does not light up. | 1. LED 2. Combination Meter 3. Wire Harness 4. ECM |
COMBINATION METER (Indicator Light):
|
Symptom |
Suspect Area |
| Cruise control indicator light does not light up. | 1. LED 2. Combination Meter 3. Wire Harness 4. ECM |
| High-beam indicator light does not light up. | 1. LED 2. Combination Meter 3. Wire Harness 4. Headlight System |
| Turn indicator light does not light up. | 1. LED 2. Combination Meter 3. Wire Harness 4. Turn Signal and Hazard Warning System |
| Shift indicator lights do not light up. | 1. LED 2. Combination Meter 3. Park/Neutral Position Switch 4. Wire Harness |
| Only one shift indicator does not light up. | 1. LED 2. Combination Meter |
| Malfunction indicator light does not light up. | 1. LED 2. Combination Meter 3. Wire Harness 4. ECM |
| ECT PWR indicator light does not light up. | 1. LED 2. ECT Pattern Select Switch 3. Combination Meter 4. Wire Harness 5. ECT System |
| 2nd start ETCS indicator light does not light up. | 1. LED 2. Combination Meter 3. Wire Harness 4. ECM |
| Center Diff. lock indicator light does not light up. | 1. LED 2. Combination Meter 3. Transfer 4WD Position Detection Switch 4. Wire Harness |
| Indicator lights do not light up. (Except Turn, Hi-beam and security) | 1. GAUGE2 Fuse 2. Wire Harness |
DEFOGGER SYSTEM:
|
Symptom |
Suspect Area |
| All defogger systems do not operate. | 1. DEFOG Fuse 2. DEFOG Relay 3. Defogger Switch (Integration Control Panel Assembly) 4. Wire Harness |
| Rear window defogger does not operate. | 1. Defogger Wire 2. Choke Coil 3. Wire Harness |
| Mirror defogger does not operate. | 1. MIR HTR Fuse 2. Engine Room J/B Relay Circuit 3. Mirror Defogger 4. Wire Harness |
POWER WINDOW CONTROL SYSTEM: This system uses the multiplex communication system, so check diagnosis system of the multiplex communication system before you proceed with troubleshooting.
|
Symptom |
Suspect Area |
| All the power windows do not operate. (Power Door Lock System is normal.) |
1. P/W (FL, FR, RL, RR) Fuse 2. Power Window Master Switch 3. Wire Harness |
| Only the driver's window does not operate. | 1. Power Window Master Switch
2. Body ECU 3. Power Window Motor 4. Wire Harness |
| "Window lock function" does not operate. | 1. Power Window Master Switch |
POWER DOOR LOCK CONTROL SYSTEM: This system uses the body control system, so check diagnosis system of the body control system before you proceed with troubleshooting.
|
Symptom |
Suspect Area |
| All the doors cannot be locked or unlocked. (Power Window Control System is normal.) |
1. DOOR Fuse 2. Door Lock Control Switch 3. Wire Harness 4. Body ECU |
| Only one side door lock control does not operate | 1. Door Lock Motor 2. Wire Harness |
| Door key related function does not operate. | 1. Door Key Lock and Unlock Switch
2. Wire Harness 3. Body ECU |
| Key confinement prevention function does not operate | 1. Key Unlock Warning Switch 2. Door Courtesy Switch 3. Wire Harness |
POWER SEAT CONTROL SYSTEM:
|
Symptom |
Suspect Area |
| Both driver and passenger power seats do not operate. (Door lock does not operate.) |
1. ALTS Fuse 2. Wire Harness |
| Driver's seat does not operate | 1. LH SEAT Fuse 2. Power Seat Switch (D) 3. Wire Harness |
| Passenger's seat does not operate. | 1. RH SEAT Fuse 2. Power Seat Switch (P) 3. Wire Harness |
| "Slide operation" does not operate. | 1. Power Seat Switch (D, P)
2. Wire Harness 3. Slide Motor (D, P) |
| "Front vertical operation" does not operate. | 1. Power Seat Switch (D, P)
2. Wire Harness 3. Front Vertical Motor (D, P) |
| "Lifter operation" does not operate. | 1. Power Seat Switch (D, P)
2. Wire Harness 3. Lifter Motor (D, P) |
| "Reclining operation" does not operate. | 1. Power Seat Switch (D, P)
2. Wire Harness 3. Reclining Motor (D, P) |
| "Lumbar support operation" does not operate. | 1. Power Seat Switch (D)
2. Wire Harness 3. Lumbar Support Motor (D) |
(D): Driver's Seat
(P): Passenger's Seat
POWER MIRROR CONTROL SYSTEM:
|
Symptom |
Suspect Area |
| Mirror does not operate. | 1. ACC Fuse 2. Mirror Switch 3. Wire Harness |
| Mirror operates abnormally. | 1. Mirror Switch 2. Mirror Motor 3. Wire Harness |
SEAT HEATER SYSTEM:
|
Symptom |
Suspect Area |
| Seat heaters do not operate. (Driver's and Passenger's) |
1. SEAT HTR Fuse 2. Seat Heater Switch (D, P) 3. Wire Harness 4. Seat Heater |
| Driver's seat heater does not operate. | 1. Seat Heater Switch (D, P) 2. Wire Harness |
| Passenger's seat heater does not operate. | 1. Seat Heater Switch (D, P) 2. Wire Harness |
| Seat heater temperature is too hot. | 1. Seat Heater |
AUDIO SYSTEM:
|
Symptom |
Suspect Area |
| Audio system abnormal operation. | TROUBLESHOOTINGS |
MULTI DISPLAY:
|
Symptom |
Suspect Area |
| Clock will not operate. | TROUBLESHOOTING |
| Clock loses or gains time. | TROUBLESHOOTING |
GARAGE DOOR OPENER SYSTEM:
|
Symptom |
Suspect Area |
| The equipment of which code has been registered does not operate. | 1. Garage Door Opener Switch
2. Wire Harness 3. * |
| LED does not light up. (Even though either switch is pressed.) | 1. Garage Door Opener Switch 2. Wire Harness |
| LED does not light up. (Only one switch is pressed.) | Garage Door Opener Switch |
* As the GARAGE DOOR OPENER on the vehicle side seems to be normal, check the OPENER on the equipment side, of which code has been registered.
ENGINE IMMOBILIZER SYSTEM:
|
Symptom |
Suspect Area |
| Engine immobilizer system does not operate. | See DIAGNOSIS SYSTEM |
HORN SYSTEM:
|
Symptom |
Suspect Area |
| Horn system does not operate. | 1. HORN Fuse 2. Engine Room J/B Relay Circuit 3. Horn Switch 4. Horn 5. Wire Harness |
| Horns blow all the time. | 1. Engine Room J/B Relay Circuit
2. Horn Switch 3. Wire Harness |
| One horn operates but the other horn does not operate. | 1. Horn 2. Wire Harness |
| Horns operate abnormally. | 1. Engine Room J/B Relay Circuit
2. Horn 3. Wire Harness |