Toyota
Toyota Land Cruiser
 Service Manual
Suspension & Axle Front axle hub
Installation

1. INSTALL AXLE HUB TO STEERING KNUCKLE

(a) Place the axle hub with disc to the steering knuckle.

NOTICE: Be careful not to damage the ABS speed sensor rotor and oil seal.

(b) Install the outer bearing.

(c) Install the claw washer.

2. ADJUST PRELOAD

(a) Install the adjusting nut and using SST, tighten it.

(a) Install the adjusting nut and using SST, tighten it.

SST 09607-60020 Torque: 59 N·m (600 kgf·cm, 43 ft·lbf)

(b) Turn the axle hub several times to settle down the bearing.

(c) Using SST, loosen the adjusting nut until it can rotate by hand.

SST 09607-60020

(d) Using SST, retighten the adjusting nut.

SST 09607-60020

Torque: 4.3 - 6.5 N·m (44 - 66 kgf·cm, 38 - 57 in.·lbf)

HINT: Check that there is no looseness on the bearing.

(e) Using a spring tension gauge, measure the preload.

(e) Using a spring tension gauge, measure the preload.

Preload (at starting): 42 - 67 N (4.3 - 6.8 kgf, 9.5 - 15.0 lbf)

3. INSTALL LOCK WASHER AND LOCK NUT

(a) Install a new lock washer and the lock nut.

(b) Using SST, torque the lock nut.

(b) Using SST, torque the lock nut.

SST 09607-60020

Torque: 64 N·m (650 kgf·cm, 47 ft·lbf)

(c) Check that the axle hub rotates smoothly and there is no looseness on the bearing.

(d) Using a spring tension gauge, check the preload.

(d) Using a spring tension gauge, check the preload.

Preload (at starting): 42 - 67 N (4.3 - 6.8 kgf, 9.5 - 15.0 lbf)

HINT: Make sure to check preload in the direction of rotation.

If the preload is not within the specified value, adjust it again with the adjusting nut.

(e) Secure the lock nut by bending one of the lock washer teeth inward and the other lock washer teeth outward.

4. INSTALL FLANGE

(a) Place a new gasket in position on the axle hub.

(b) Install the flange to the axle hub.

(c) Install the 6 cone washers, washers and new nuts.

Torque: 33 N·m (335 kgf·cm, 24 ft·lbf)

(d) Pull out the drive shaft to the outside of the vehicle and

(d) Pull out the drive shaft to the outside of the vehicle and select the snap ring which ensures the clearance between the tip of the flange and the snap ring is less than 0.2 mm (0.008 in.).

Snap ring thickness:

(e) Using a snap ring expander, install a new snap ring to the

(e) Using a snap ring expander, install a new snap ring to the drive shaft.

(f) Install a new grease cap to the flange.

5. INSTALL BRAKE CALIPER

(a) Install the brake caliper, washers and 2 bolts.

Torque: 123 N·m (1,250 kgf·cm, 91 ft·lbf)

(b) Install the flexible hose and bolt to the steering knuckle.

Torque: 28 N·m (290 kgf·cm, 21 ft·lbf)

6. INSTALL FRONT WHEEL

Torque: 131 N·m (1,340 kgf·cm, 97 ft·lbf)

7. CHECK ABS SPEED SENSOR SIGNAL ( DI-505 )

    More about Front axle hub:

    Disassembly

    Installation

    Reassembly

    Removal

    Toyota Land Cruiser Service Manual / Suspension & Axle / Front axle hub / Installation

    Toyota Land Cruiser Service Manual

    Categories


    2011-2018 Copyright www.tlacruiser.com