Toyota
Toyota Land Cruiser
 Service Manual
Transfer Rear extension housing
Reassembly

HINT: Coat all of the sliding and rotating surfaces with gear oil before reassembly.

1. INSTALL BALL BEARING

(a) Using SST and a press, install the ball bearing.

(a) Using SST and a press, install the ball bearing.

SST 09316-6001 1 (09316-00011, 09316-00031)

(b) Select a snap ring that will allow the minimum axial play.

(b) Select a snap ring that will allow the minimum axial play.

(c) Using a screwdriver, install a new snap ring.

(c) Using a screwdriver, install a new snap ring.

2. INSTALL DUST DEFLECTOR

(a) Using SST and a hammer, install a new rear extension

(a) Using SST and a hammer, install a new rear extension housing dust deflector.

SST 09316-6001 1 (09316-00011, 09316-00041)

(b) Using SST and a press, install a new rear output shaft

(b) Using SST and a press, install a new rear output shaft dust deflector.

SST 09316-2001 1, 09316-60011 (09316-00011)

3. INSTALL OIL SEAL

(a) Apply MP grease to the lip of a new oil seal.

(a) Apply MP grease to the lip of a new oil seal.

(b) Using SST and a hammer, drive in the oil seal.

SST 09316-6001 1 (09316-00011, 09316-00031)

4. INSTALL REAR OUTPUT SHAFT

(a) Using SST and a press, install the rear output shaft.

(a) Using SST and a press, install the rear output shaft.

SST 09316- 20011, 09316- 60011 (09316- 00011, 09316-00031)

(b) Install the 2 seal rings to the rear output shaft.

(c) Select a snap ring that will allow the minimum axial play.

(c) Select a snap ring that will allow the minimum axial play.

(d) Using a snap ring expander, install a new snap ring.

(d) Using a snap ring expander, install a new snap ring.

5. INSTALL SPEED SENSOR DRIVE GEAR

(a) Install the speed sensor drive gear.

(b) Using a snap ring expander, install the snap ring.

6. INSTALL OIL PUMP PLATE

(a) Install the oil pump plate.

(a) Install the oil pump plate.

(b) Install and torque the 3 bolts.

Torque: 4.9 N·m (50 kgf·cm, 43 in.·lbf)

7. INSTALL VALVE SEAT, BALL, SPRING AND SCREW PLUG

(a) Apply gear oil to the ball.

(a) Apply gear oil to the ball.

(b) Install the valve seat, ball and spring.

(c) Apply liquid sealer to the screw plug threads.

Sealant: Part No. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent

(d) Using a hexagon wrench, install and torque the screw plug.

Torque: 29 N·m (300 kgf·cm, 22 ft·lbf)

8. INSTALL DRIVEN ROTOR

(a) Apply gear oil to the driven rotor.

(a) Apply gear oil to the driven rotor.

(b) Install the driven rotor.

9. INSTALL DRIVE ROTOR

(a) Apply gear oil to the drive rotor.

(b) Install the drive rotor.

HINT: Align the alignment marks.

10. INSTALL OIL PUMP COVER

(a) Install the oil pump cover.

(a) Install the oil pump cover.

(b) Using a torx socket wrench (T30), install and torque the 3 screws.

Torque: 4.9 N·m (50 kgf·cm, 43 in.·lbf)

NOTICE: Align the oil hole of the rear extension housing and oil groove end of the oil pump cover.

11. INSTALL OIL PUMP DRIVE SHAFT

    More about Rear extension housing:

    Disassembly

    Inspection

    Reassembly

    Toyota Land Cruiser Service Manual / Transfer / Rear extension housing / Reassembly

    Toyota Land Cruiser Service Manual

    Categories


    2011-2018 Copyright www.tlacruiser.com